Skip to content
Call (909) 922-1858Licensed, bonded & insured · License #585047

Undermount Sink Cutouts & Installation in Rancho Cucamonga, CA

Rancho Cucamonga Custom Countertops provides undermount sink cutouts & installation in Rancho Cucamonga, CA, with every opening made in our shop to your sink's own template. The edge is polished, the reveal is your choice and the basin is carried by real brackets. We serve San Bernardino County homeowners, remodelers and cabinet shops.

  • Free template visit
  • Seams approved before a cut
  • One written quote

Get a free template visit or a bid

About our undermount sink cutouts

An undermount sink hangs below the stone, so the opening is a visible, finished edge that has to be right the first time. We cut each opening from your sink's template, polish the inside face and glue the mounting hardware to the stone, for homes, bath remodels and light commercial counters alike. The crew that templates the cabinets is the crew that sets the sink.

Whether it is a single-bowl kitchen sink, a pair of rectangular basins in a vanity or a heavy farmhouse apron, we plan the support before the first cut. Serving Rancho Cucamonga, Upland, Fontana and Ontario, we keep template and install close together and leave an opening that looks like it grew out of the stone.

How we work

One Crew From Template to Install

Homeowners get a free template visit. Contractors, cabinet shops and builders get tops to their schedule.

Same crewThe crew that templates your cabinets is the crew that installs the tops
Seams approved firstSeam layout marked on your chosen slab and approved before anything is cut
Cut in the shopEvery cut made wet in the shop, never in your home
CA License #585047Licensed, bonded and insured

Why every opening is made at the shop table

Every undermount opening is cut in our shop because that is the only place the slab can be supported properly while the saw and router work. The cut edge of an undermount is on display, since you see it every time you wipe a crumb into the basin, and a chipped or wavy line is permanent. A shop table, wet cutting and a polishing station give a clean radius and a smooth reveal that a hand tool over installed cabinets cannot match.

To cut an opening that fits, we need three things from you at the template visit:

  • The sink itself, or its exact model number and the manufacturer's cutout template.
  • The faucet and any soap dispenser, filter tap or air switch, so the holes are drilled in the right places.
  • A decision on the reveal, which we explain below, made while looking at the actual sink.
  • Your cabinet drawings or a look at the installed base, so we know where the sink bowl, the cabinet rails and the dishwasher sit.

A cutout drawn from a generic size leaves you with gaps or a lip, and both are hard to fix once the stone is polished. Working from the real sink removes the guesswork.

Positive, Zero and Negative Reveals

The reveal is how the stone sits relative to the sink's top rim, and it changes both the look and the cleaning. Because the reveal is set by where the opening is cut, it cannot be adjusted after fabrication, which is why we show you the options with your sink in hand before we start. These are the three choices:

Positive reveal

The opening is cut slightly larger than the sink, so a narrow band of rim shows around the edge. It forgives small variations in the sink and in the setting, and it is the easiest to get right. The ledge can catch a little grime, so it needs a wipe along the rim.

Zero reveal

The edge of the stone lines up with the inside wall of the sink, giving a flush, clean line. It looks tidy and wipes easily, but it needs a precise cut and exact placement of the sink during install.

Negative reveal

The stone overhangs the basin by a small amount, hiding the rim entirely. It looks sharp and modern, but the overhang makes it harder to sweep water and crumbs into the bowl, and it exposes the edge of the stone to knocks from pots.

How the Sink Is Held Up

A sink is held to the underside of the countertop by hardware, and the sealant between them keeps water out rather than carrying weight. A full cast iron basin can weigh well over 100 pounds before it holds a single dish, and water and cookware add to that. We size the support to the sink you actually bought, using these parts:

Clips and brackets

Metal clips or brackets are epoxied to the back face of the slab and then clamped or screwed to the sink. They spread the load across the slab instead of leaving it on a bead of caulk.

Rails and frames for heavy bowls

A big single-bowl, a cast iron or fireclay sink or a farmhouse front gets added support, either wood rails fixed to the cabinet or a frame below, so the cabinet shares the weight with the stone.

Sealant at the joint

A neutral-cure silicone seals the joint between the stone and the rim. It is the water barrier, and it needs a clean, dry bond line to work.

Faucet and accessory holes

Holes for a faucet, sprayer or dispenser are drilled in the shop, and their spacing is checked against the faucet's spec so nothing sits too near the sink edge.

Estimated Undermount Sink Cutout Costs in Rancho Cucamonga

Cutouts on countertops we fabricate are part of the job price, and the charges below apply mostly to extra openings and to work on stone you already own. An additional prep sink or bar sink opening is typically estimated at roughly $150 to $400, depending on the size of the bowl, the stone and the edge detail. Converting a drop-in to an undermount in an existing top is typically estimated at roughly $300 to $800, and a remount of the same sink with fresh sealant is typically estimated at roughly $200 to $500.

Several things move those numbers:

  • The material, since quartz and dense granite take more blade and polishing time than a softer stone.
  • The sink's corner radius. A tight-cornered rectangular bowl needs finer shaping than a rounded one.
  • Whether the stone is already installed or can come to the shop.
  • Added support for a heavy cast iron or farmhouse basin.
  • Cracks, seams or thin sections near the opening that need repair or reinforcement.
  • Faucet holes and extra accessories, drilled one by one.

All figures are estimates for Rancho Cucamonga, and they can change with the sink and the condition of the stone. The written quote after the template visit gives the final price, with the sink work listed as its own line.

Adding an Undermount to Stone You Already Have

In many kitchens an old drop-in sink can be converted to an undermount without replacing the countertop, provided the stone is thick, sound and well supported. The job is to enlarge the opening, cut a polished new edge and mount the new basin below. The stone is usually removed or taken to the shop, because the quality of the polish depends on being able to work it flat on a table.

Before we promise anything, we inspect the top for the conditions that decide whether it is safe:

  • Hairline cracks, especially running to the corners of the old opening.
  • Seams close to the sink, which have little stone to spare.
  • Thin sections between the opening and the front edge or the cooktop.
  • Thickness, since 2 centimeter stone often needs a build-up or extra support at the new edge.
  • How the top was originally fixed to the cabinets.

If the answer is no, we say so and suggest the better route. That may be a repair, or replacing the top while the sink is out, but we would rather tell you early than split a slab.

White quartz counter run with faint grey veining, a stainless undermount sink and a brass gooseneck faucet

Which Surfaces Take an Undermount Sink

Undermount sinks suit solid, dense surfaces that can be cut, edged and polished along a vertical face. Granite, quartz and quartzite are the usual choices, and marble works when you accept its softer, etch-prone character around a wet zone. A solid surface top can also take an undermount, often with a bonded rim detail.

Laminate and tile are not good candidates, because their cut edges cannot be finished or sealed against water. A raw laminate edge swells when it gets wet, and grout joints do not hold a sink.

Thickness matters too. Stone at 3 centimeters carries a bowl without much fuss, while a thinner top may need a laminated front edge and extra rails. We check the material and the thickness at the template and tell you which of the options will work for your sink.

Quartzite counter with gold and grey veining book-matched so the pattern mirrors across the seam

Finishes and Edges We Fabricate

The process

From First Call to Finished Top

Four steps, and nothing is cut until you have approved the slab and the seam layout.

  1. Call or send the form

    Homeowners book a free template visit. Remodelers and cabinet shops send the sink and cabinet details for a bid.

  2. Pick the sink and the reveal

    You choose the sink, the faucet and the reveal, and we confirm the model against its cutout spec.

  3. Template and shop cut

    We template on your cabinets, then cut the opening wet, shape the corners and polish the edge in the shop.

  4. Mount and seal

    We bond the hardware, set the sink, seal the joint and leave the plumbing reconnection to a licensed plumber.

Questions

Undermount Sink Cutouts & Installation: Common Questions

What does an undermount sink cutout cost in Rancho Cucamonga?

On a new top we fabricate, the cutout is part of the job, and a second or prep sink is typically estimated at roughly $150 to $400 per extra opening. Retrofits into stone you already own are quoted after inspection. These are estimates, and the written quote after the template visit sets the number.

Can I turn my drop-in sink into an undermount?

Often, when the slab is thick and free of damage. The opening is widened, the new edge is polished and the new basin goes in from below. First we look at cracks, seams and the distance to the cooktop and dishwasher first, because the wrong cut can ruin a top that is otherwise fine.

Does the sink need to be delivered before the template visit?

Ideally, and if it has not arrived, send the exact model number. We cut from the maker's own template for that bowl, because an estimated size can leave the opening a quarter inch off. Have the faucet or its spec sheet ready as well, so the tap holes land where the plumber needs them.

How much sink rim should show inside the opening?

That visible band is called the reveal. Zero reveal sits flush with the stone, a positive reveal shows a narrow band of rim, and a negative reveal lets the stone overhang the basin. Most households choose zero or a small positive reveal, and we show you each before we cut.

Will the sink eventually drop?

Not when it is mounted correctly. The bowl hangs from metal hardware epoxied into the stone from below, with added rails for a heavy basin, and the silicone only seals the joint. A sink that hangs on adhesive alone is the one that fails.

Does a granite or quartz top need special care around the sink?

Keep the rim wiped, because standing water at the joint is what eventually breaks down a seal. Check the caulk line each year and reseal it if it looks gray or lifted. Our sealing service covers the stone itself when it needs attention.

Can you cut the opening on site if the top is already installed?

We avoid it. Dry on-site cutting makes dust and risks chipped edges, and the polished reveal cannot be finished properly over cabinets. When an existing top has to be modified, we usually take it back to the shop, or tell you plainly if it should be replaced.

How long does an undermount sink swap take?

A like-for-like swap is often finished in a day, with the plumber returning after the adhesive cures. A retrofit that changes the opening takes longer because the stone goes to the shop. We give you the schedule once we have seen the top.

Free template visit

Talk to us about undermount sink cutouts

Homeowners get a free template visit. Remodelers and cabinet shops can send the sink and cabinet details for a bid.

Call (909) 922-1858

Licensed, bonded & insured · License #585047. Calls only, we do not receive text messages.

Call (909) 922-1858Licensed, bonded & insured · License #585047